Website

What're your opinions about How to Install a Bathtub?

Mounting a bathtub isn't precisely brain surgery, but it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately hard job. If the old tub is easily easily accessible, the project can move quickly; if you need to open up a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need a helper to move out the old tub and also set in the brand-new one. Ensure you have actually certified on your own for the task as well as fit attempting it. Instead of hiring a contractor to take over a halfway-completed job, it is far better to think about employing one prior to you start. Chances are you might need a professional plumber to make tube links.
This short article will certainly assist you install a new bathtub in your restroom if you have currently gotten a new tub as well as do not require to alter the plan of your previous water supply pipelines.
Your tools and also product list should make up the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old taps with new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain any water staying in the system. The procedure of removing the existing taps can be quite bothersome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Before proceeding to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

Fitting New Taps

If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin making sure that the washing machines are in area in between the tap as well as the sink. Protect the faucet in position with the manufacturer given backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet adapters. The previous kind ought to be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

Installing the Bath tub

Using both wood boards under its feet, position the bathtub in the needed setting. The wood boards are valuable in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub till the spirit level checks out level.
To mount faucets, fit all-time low of the furthest flexible tap port to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Switch on the water supply as well as inspect all joints and brand-new pipework for leakages as well as tighten them if needed. Fill the tub and also check the overflow outlet and the regular electrical outlet for leaks.
Lastly, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub ought to wait till the bathtub has actually been made use of at least once as this will certainly settle it into its last position.

Getting ready for the Installment

Firstly, the sustaining framework provided with the bathroom ought to be fitted (if needed) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to stop stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be suited its final position.

Tiling Around the Tub

In the location where the bath meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture an inflexible seal, causing the water to penetrate the wall between the bath as well as the tiling, bring about complications with wetness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and installations. They are offered in tubes as well as cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can break relatively early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently offered on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant adhesive as well as cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you enjoy reading up on How to Install a Bathtub Yourself? Place feedback below. We will be interested to know your feelings about this article. We are looking forward to see you back again in the future. In case you appreciated our blog posting if you please don't forget to pass it around. Thank you so much for taking the time to read it.

Browse Website